This tutorial describes how to interface ADC to based Mircocontroller. The article also provides a sample tested Technology is an online. In This project (AT89S52) Microcontroller is interfaced with ADC IC to show the output value of ADC on LCD Screen,for a given variable input voltage. Interfacing ADC with three LDR using microcontroller and LCD. The project includes circuit diagram and source code in C.

Author: Taujinn Zolonos
Country: Saint Lucia
Language: English (Spanish)
Genre: Politics
Published (Last): 21 July 2014
Pages: 203
PDF File Size: 16.61 Mb
ePub File Size: 10.99 Mb
ISBN: 462-9-95328-897-2
Downloads: 32139
Price: Free* [*Free Regsitration Required]
Uploader: Faushakar

Interfacing with ADC – Just Execute It

In this project we have applied frequency by using microcontroller. Hope this helps CODE: Whereas the conversion is begun on the falling edge i. Typically, an ADC is an electronic device that converts an input analog voltage or current interfaccing a digital number proportional to the magnitude of the voltage or current.

You are commenting using your WordPress. This device has three channel address line namely: The circuit of A-to-D converter shown here is configured around ADCavoiding the use of a microprocessor.

This high-density System-in-Package SiP integrates controller, power switches, and support components. And then microcontroller changes ADC channel by using address line. Arduino based Interfacjng receiver.

The input which is to be converted to digital form The output pins of ADC are connected to the port P0 of the controller. Interfacing ADC To Then microcontroller shows its value at Ch1 position in LCD. A 9 volt battery and a 5 volt voltage regulator namely are used for powering the circuit. The adv0808 value of Wihh varies in the range 0 to Interface GPS with Arduino. This is an intermediate circuit which finds several applications. It is a 14 pin IC with two internal D flip flops.


Interfacing ADC/ADC with Microcontroller

This circuit can be wiith as an intermediate circuit in many applications. Digital computers use binary values, but in physical world everything is analog. The output is taken on the LED s.

SC pin6 of controller is connected to P1. What is Web Browser. Therefore, we need an analog-to-digital converter to translate these analog signals to digital signals.

Every time the timer completes the counting, pin P1. Digital computers use binary values, but in physical world everything is analog.

How to interface three input channels of ADC0808 using 8051 microcontrollers (AT89C51)

And show on LCD as name Ch2. Controller interrupt is used to generate the clock for driving the ADC It witu on the principle of successive approximation. Notify me of new comments via email.

An LDR will detect the intensity of light and generate voltage depending upon light intensity. Fill in your details below or click an icon to log in: It accepts a binary coded decimal as input and converts it into a pattern to drive a seven-segment for displaying digits 0 to 9.

In parallel ADC we have 8 or more pins dedicated to bringing out the binary data. acd0808

Interfacing 8051 with ADC 0808

It has a total of eight analogue input channels, out of which any one can be selected using address lines A, B and C. A 16×2 LCD display interafcing very basic module and is very commonly used in various devices and circuits. The circuit diagram shows the connection of the D flip-flop ICs. This Code is only visible to Registered users.


EOC, pin7 is connected to pin3 P1. The resistance decreases as the intensity of incident light increases, and vice versa. The input control signal SC, being adx0808, initiates start of conversion at falling edge of the pulse, whereas the output signal EOC becomes high after completion of digitization.

The ADC chips are either parallel or serial. In the knterfacing of light, LDR exhibits a resistance of the order of mega-ohms which decreases to few Normally analogue-to-digital converter ADC needs interfacing through a microprocessor to convert analogue data into digital format. To enable the Timer0 in interrupt enable mode, the register IE is loaded with the value 0x The circuit uses the first analog input pin to take the analog input signals from the preset.

Started working on this website as an Hobby and now its a full time venture. The resistance is varied by An analog-to-digital converter is a device which converts continuous signals to discrete digital numbers.

ADC needs an external clock to run. Choosing Motor For Robots.