Préampli-Processeur CHORD DSP R VENDU TRÈS RARE! Préampli processeur exceptionnel en HC et, fait beaucoup plus rare. Chord dsp r preamp / surround controller, boxed. CHORD DSP R preamp/ surround controller. with dts and dolby 2 surround. Introduction The Chord DSP forms the centre of a High -End cinema and audio system. The DSP decodes Dolby Digital, DTS and DTS-ES and has the.

Author: Zuluzahn Daikinos
Country: Romania
Language: English (Spanish)
Genre: Photos
Published (Last): 9 January 2013
Pages: 45
PDF File Size: 2.67 Mb
ePub File Size: 2.28 Mb
ISBN: 286-1-27439-210-2
Downloads: 24592
Price: Free* [*Free Regsitration Required]
Uploader: Kajit

The Menu title will only display six characters and so will only display DSP Usually acoustic di stance is much longer and may even vary on the same conditions. This function is called Late Night as it is useful to use late at night when chlrd do not wish to listen to loud and dynamic soundtracks. We recommend that an earthing method for your dsp8000f be implemented.

The trigger output is activated when a composite video input signal is detected SVideo The trigger output is activated when a SVideo input signal is detected VidSign The trigger output is activated when either a SVideo or composite video input signal is detected Vidsrc The trigger output is activated when any video source is selected Audiosrc The trigger output is activated when any audio source is selected Trigger 1 polarity This setting is used to determine the polarity of the trigger when it is activated.

These give an indication of the channels that are present in the incoming signal program format.

You should then adjust each loudspeaker level setting so that the SPL meter reads the same measurement for each loudspeaker tone. It’s a community-based project which helps to repair anything.


Use this LCD touch pad to toggle between the two available settings.

If your equipment has unbalanced analogue audio outputs you should always connect to the DSP by these inputs even if you are connecting your equipment also by digital connections. Movie soundtracks can sometimes sound quite bright because they have been mixed to suit the acoustics of cinemas. The subwoofer crossover frequency can be set from 40 Hz to Hz in steps of 10 Hz.

This is useful if you make a mistake when making changes. This can happen due to video processing – in projectors, plasma screens and standalone video processors. A BNC converter module is available on request.

Used chord dsp for Sale |

This button functions as a toggle to mute and un -mute the outputs. MIC This input is used to connect a microphone. This input also allows another bypass route for use with sources that need to avoid the digital processing boards in the DSP Instead, they are redirected to the front large choed or the subwoofer if present.

No change Analog monitor Component video: Treble This setting allows you to adjust the treble or high frequency content of the main audio output.

DSP 8000 AV Processor

Distance setup The distances of all your speakers dsp8000r the listening position are entered so that the DSP can automatically the required correct delays for a full surround image as intended. Their default names and the order in which they appear are listed in the section above. They are also less prone to interference than unbalanced inputs.

Lipsync delay Preset This setting calls up any one of the 5 five presets and its currently saved levels. Otherwise these trigger outputs may be damaged. It allows you to set the balanced audio inputs to any one of the ten sources.


吏„?•?œ ?„濡œ GLV – Create arts through technology!

These buttons are featured on the front panel and on the remote control. Press the ESC LCD touch pad or front panel button if you wish dsp8000r keep the previous gain settings Component video This setting allows you to assign a component video input signal to the selected source. Press this LCD touch pad to increase the value of a selected parameter within the set up menu.

VOL Press this mechanical button to decrease the main volume of the audio outputs. The volume knob also acts as a push button. Turning on the tape monitor function on will direct the audio signal coming from your recording device to the main outputs of the processor. The information that is shown includes the selected input source, the signal type, any music mode that is selected, the video format and the current volume settings.

This should be used at all times. The information that is shown is the current selected input source that is assigned to the zone output, the currently selected mode and the zone volume. S-video IN 1 and analogue audio IN 1. Chord guarantee registration card 5 when setting up To ensure cyord your Chord processor works efficiently and safely, please pay particular attention to the following issues.