FRENIC LIFT MANUAL PDF

FRENIC LIFT MANUAL PDF

FRENIC-Lift. FRENICG11S/P11S. FRENICVG7S. User’s Manuals and Technical Information. FRENIC-Multi User’s Manual. FRENIC-Eco User’s. FRENIC-Lift is an inverter designed to drive a three-phase induction motor ( hereafter For details about this product, refer to the FRENIC-Lift User’s Manual that. The FRENIC-Lift Series of exclusive AC Drives for operation of elevators are FRENIC-Lift AC Drives are available in a series with capacities ranging from

Author: Faukus Volkree
Country: Nepal
Language: English (Spanish)
Genre: Music
Published (Last): 24 October 2017
Pages: 386
PDF File Size: 19.6 Mb
ePub File Size: 1.51 Mb
ISBN: 627-1-66334-261-7
Downloads: 67063
Price: Free* [*Free Regsitration Required]
Uploader: Brajora

Page Fuji Electric Co. Maximum speed F03 2 The reference torque bias follows the input voltage level on terminal [12]. In this case, take countermeasures such as installing the inverter in a place that easily protects human body from electric shock. Page 77 [ 16 ] Run operation error Problem You incorrectly operated the inverter.

Terminal Arrangement And Screw Specifications 2. Page 41 Table 2. Brake control by output current Operation level 0 to ON delay time 0.

Put the front cover back in reverse order of.

This chapter lists specifications including output ratings, control system, external dimensions and protective functions. Precautions For Use Precautions for use Driving a V When driving a V general-purpose motor with an inverter using ex- general-purpose tremely long wires, damage ftenic the insulation of the motor may occur. Page 22 3 For inverters with a capacity of 30 kW or above Removing and mounting the cover To remove the front cover, loosen the four fastening screws, hold it with both hands, and slide it upward.

Ensure that the circuit breaker capacity is equivalent to or lower than the recommended capacity. The first letter is an alphabet that identifies its group and the following two letters are numerals that identify each individual code in the group.

  ASCE 7-98 PDF

Torque bias gain adjustment BTBG. Each function code consists of a 3-letter string. Name of option Function and application Insert an MC in the power source side of the inverter in crenic to: If any rfenic these conditions has occurred, either eliminate the abnormal or manuak factor s and perform tuning again, or contact your Fuji Electric representative.

Refer to Figure 2. FRENIC-Lift is an inverter designed to drive a three-phase induction motor hereafter called an induction motor and a three-phase permanent magnet synchronous motor hereafter called a synchronous motor for exclusively controlling elevating machinery. Page 14 2 Warning plates Figure 1. Page 37 Table 2. Page 29 Follow the procedure below for mnaual and configuration of the inverter.

Brake control by time 2: Follow the procedure below for wiring and configuration of the inverter.

Please do not use it with other products. Don’t show me this message again. Page 19 3 Mounting direction Horizontal layout is recommended when two or more inverters are to be installed in an equipment or enclosure.

Set up L02 for correct data. Possible Causes What to Check and Suggested Measures 1 No power supplied to the Check the input voltage, output voltage and interphase voltage unbalance.

Fuji Electric FRENIC-Lift series Instruction Manual

Lower the temperature around the motor. Page Name of option Function and application Insert an MC in the power source side mahual the inverter in order to: Consult your Fuji Electric representative if these terminals lidt to be used. Enable data prot ection Note: When the dielectric strength test is necessary, contact your Fuji Electric representative. On the bottom are no case fixing screws. The 1st week of January is indicated as ’01’. Page 39 Table 2. Init ialize all function code data to t he factory defaults H04 Auto-resetting 0: Driving gener- When high starting torque is required or quick acceleration or deceleration al-purpose motor Selecting is required, select an inverter with a capacity one size greater than the inverter standard.

  HYPERLYNX TRAINING PDF

Otherwise fire could occur. Page 35 Table 2. Mounting the covers Put the front cover to the inverter case so that its bottom engages with the ,ift provided on both sides of the case.

FRENIC-Lift | Fuji Electric Global

If any problems persist after the above recovery procedure, contact your Fuji Electric representative. Push the front cover against the case of the inverter and slide it upward until the latch at its top engages with the case.

Doing so could cause failure. Removing the cable guide plate Before to proceed, remove the terminal block cover as frenjc below left.

Don’t have an account? Also remove the case fixing screws from the top. When the replacement is necessary, contact your Fuji Electric representative. Designed for Elevating Machinery. Trip with alarm after running for t he period specified by timer y03 2: Take an attention for this structure to connect wires to main output secondary terminals. The standard motor and the inverter motor are protected in the range of all the frequencies. The case fixing screws are not necessary in external cooling.