INTERSEAL HS – PART B (REGULAR) – L () Use; Colors; MSDS / TDS; Variant; Product Review(s). Use For immersion service, Interseal HS must be applied to surfaces blast cleaned to SSPC-SP10 or Sa PT. International Paint Indonesia. Safety Data Sheet EGA INTERSEAL HS GREY PART A Version Number 2 Revision Date 06/27/ 1. Product and . International Paint Ltd. Safety Data Sheet. EGA Interseal HS Grey Part A. Version No. 2 Date Last Revised 05/10/ Conforms to the requirements of.

Author: Mikakinos Goshakar
Country: Cayman Islands
Language: English (Spanish)
Genre: Relationship
Published (Last): 17 January 2011
Pages: 424
PDF File Size: 12.10 Mb
ePub File Size: 13.2 Mb
ISBN: 344-2-93433-267-7
Downloads: 81911
Price: Free* [*Free Regsitration Required]
Uploader: Malami

Typically this would apply to C or D grade rusting in this standard. Press and move to zoom. Preferred application is by a suitable large tip hopper gun e. Systems recommendation Interseal HS will normally be applied to correctly prepared steel substrates. In common with all epoxies Interseal HS will chalk and discolor on exterior exposure.

When applying interseak methods other than airless spray, the required film build is unlikely to be achieved. Loose or flaking coatings should be removed back to a firm edge.

Further information is available from International Protective Coatings. However, it can be used over suitably primed surfaces. A surface profile of mils microns is recommended. However, these phenomena are not detrimental to anti-corrosive performance. NSF Certification is for tanks greater than gallons Interseal HS can be used as a non-skid deck system by modification with addition of GMA crushed flint aggregate.


For application to a wide variety of substrates including hand prepared rusty steel, abrasive blast cleaned and hydroblasted steel, and a wide range of intact, aged coatings. The surface to be coated mssd be clean, dry and free from contamination. Trowel or roller can be used for small areas.

Mouse over image to zoom. Warning In order to achieve inrerseal performance on hand prepared steel, the aluminum pigmented version should be applied as a primer coat by brush to ensure thorough wetting out of the substrate by Interseal HS. Always mix a complete unit in the proportions supplied. Interseal HS is suitable for overcoating intact, aged alkyd, epoxy and polyurethane systems. Typical thicknesses will be between milsmicrons. Soluble salts should be removed by fresh water washing.

Be the first to write a review for this intereal


Avoid using a mixture of application methods whenever possible. Certification is for tanks greater than gallons Smds the unit has been mixed it must be used within the working pot life specified.

Sagola or Air texture gun fitted with a mm nozzle. It is also possible to apply to damp surfaces in some circumstances. Level of sheen and surface finish is dependent on application method. Consult International Protective Coatings for further details. Dry bristle brushing will normally be adequate for accumulated dirt. Application should then be to a suitably primed surface. Prior to paint application all surfaces should be assessed and treated in accordance with ISO Provides excellent anti-corrosive protection in industrial, coastal structures, pulp and paper plants, bridges and offshore environments in both atmospheric exposure and immersion service.


With freshly blasted surfaces a slight degree of flash rusting is allowable, and is preferable to the surface being too wet. Alternatively, a broadcast method of application can be used.

INTERSEAL 670HS – PART B (REGULAR) – 0.57L (5.63 :1)

Puddles, ponding and accumulations of water must be removed. Varnish Hybrid Water base. Do not thin more than allowed by local environmental legislation. However, this product is not recommended where thermoplastic coatings such as chlorinated rubbers and ijterseal have previously been used. Surface preparation The performance of this product will depend upon the degree of surface preparation.

Surface defects revealed by the blast cleaning process, should be ground, filled, or treated in the appropriate manner. Please consult International Protective Coatings for alternative recommendations.

If salt water is used in the wet blast process the resulting surface must be thoroughly washed with fresh water before application of Interseal HS.

Premature exposure to ponding water will cause a color change, especially in dark colors. Accumulated dirt and soluble salts must be removed.

Aged Coatings Interseal HS is suitable for overcoating a limited range of intact, tightly adherent aged coatings.